Coyote Bioscience is proud to introduce the rapid halal testing kit that is portable and results can be known in minutes.
For more information, call CSI Labshop Malaysia, distributor of Coyote Bioscience halal tester qPCR instrument.
CSI Labshop Malaysia is a leading supplier of chemical and laboratory instrument. If you are finding a ULT or LT freezer for your lab, look no further. Haier has the best price performance ratio in the market with a proven success and reliability to show for. Browse our product catalog for more info.
ARE YOU LOOKING TO REPLACE YOUR OLD, BUDGET BURNING FREEZERS WITH MORE ENERGY EFFICIENT ONES?
 |
THEN LOOK NO FURTHER THAN THE LOW ENERGY RANGE FROM: |
Key Features:
• Extremely energy efficient (only 10.5kWh/24hr) saving up to 50% energy due to Hydrocarbon based refrigeration system.
• Vacuum Insulation Panel door design with additional insulation factor cuts down heat loss to the cabinet.
• Four internal compartments to keep the cold air inside.
• Simple and easy to use control panel – cabinet temp, voltage and ambient temperature readings displayed simultaneously.
• Pressure equalisation port.
• Simple temperature data collection via USB interface on display panel.
• Small footprint to capacity ratio.
• 9 visual and audible alarms.
• Self-Diagnostics – control system can automatically determine areas where there may be a problem.
• Enforced Shelves to support a heavier load.
If you are interested in Freezers, you may also be interested in:
| Racking | -40°C Deep Freezer- | |
CSI Labshop Malaysia has a comprehensive lineup of TOMY Japan SX-series vertical autoclaves designed for sterilization of media, equipment, samples, with automatic drying cycles and rapid cooling only available in TOMY autoclaves SX-series. We offer full installation, training, and commissioning setups anywhere in Malaysia. Trust our competent team to handle your autoclave needs for your laboratory. We also handle DOSH (JKKP approval and renewal) for customers. Our products come with complete service backup with TOMY renowned quality and reliability.
Maximized chamber capacity at Minimum installation space
A top-open lid, which can be operated easily with a single hand or foot, is provided with the SX autoclaves. To open the lid, the lid lock is released by stepping on the foot pedal locates at the bottom while pressing the lid down. The lid can be opened with minimal effort owing to mechanical assistance. In addition, the lid can be closed easily just by pressing it down.
The main body is very compact owing to the design which provides thorough installation space saving. In addition, installation space at the side of the main body which is required for models employing a slide-open lid, which is not necessary at SX autoclaves top-open lid. Even when several SX autoclaves are installed side-by-side, the necessary installation space is minimized.
A : 790mm(SX-300),970mm(SX-500),1003mm(SX-700)
B : 614mm(SX-300),794mm(SX-500),827mm(SX-700)
C : 410mm(SX-300/500),470mm(SX-700)
The LED display shows working status for easy monitoring. The process being performed is indicated by an LED indication lamp blinking in red.
The illuminated display on the operating panel shown in the picture is different from the actual display at the time of operation.
A rapid air-cooling function (vessel-cooling fan) permitting reduction of chamber cool down time is provided as a standard feature. This is most appropriate for lowering the temperature rapidly on completion of the cycle. The time required for lower the temperature is much reduced by employment of the cooling fan in comparison with natural cooling.
The optimal sterilizing course can be selected from among five courses, such as the liquid sterilizing course in addition to that for normal sterilization.
An easily viewable large indication “Operated” is provided at the upper section of the operating panel.
Depending on the pressure status (normal pressure/pressure is applied),the displayed color changes.
Variable temperature setting such as to 100°C as well as to 121°C has been made possible.The temperature can be set within the range from 45°C to 135°C in steps of one degree (heating mode up to 104°C).
A function allowing the exhaust valve to open automatically after completion of sterilization is provided. The exhaust speed can be set to one of six levels (set to variable for liquid sterilization）
The operation starting time can be preset easily. By presetting the start of operation, otherwise wasted periods at night or early morning, can be used effectively.
Variable temperature setting such as to 100°C as well as to 121°C has been made possible.The temperature can be set within the range from 45°C to 135°C in steps of one degree (heating mode up to 104°C).
A safety device (lid interlock mechanism) for locking the lid during operation is provided. A high level of safety is assured to prevent unanticipated accidents.
When the balance between the temperature and pressure deviates during sterilization, fine exhausting is carried out automatically in order to adjust the best chamber condition.
Functions & Features
Liquid sterilizing / Heating / Warming / Check / Last-run memory / Built-in steam exhaust bottle
Flat internal surface of the chamber / Lid opening/closing detection mechanism
Exhaust bottle detection mechanism / Leakage breaker provided
Sensor for directly detecting the temperature of articles to be sterilized. More reliable sterilization monitor can be carried out.
The temperature data, pressure data, etc. can be exported. The temperature can be recorded when the external recorder is connected.
A temperature sensor and recorder independent of the autoclaves. The chamber temperature can be recorded.
| Model name | SX-300 | SX-500 | SX-700 | ||
| Operating temperature range | Sterilizing | 105 ∼ 135°C（0.019 ∼ 0.212MPa） | |||
| Heating | 45 ∼ 104°C（0 ∼ 0.015MPa） | ||||
| Warming | 45 ∼ 95°C | ||||
| Maximum operating pressure | 0.263MPa | 0.25MPa | |||
| Temperature | Display | Digital | |||
| Pressure gauge | Display | Analog | |||
| Display range | 0 ∼ 0.4MPa | ||||
| Heat source | 1.5kW electric heater | 2kW electric heater | 3kW electric heater | ||
| Safety device | • Water level sensor, • Current leakage breaker, • Lid interlock, • Over-heat prevention, • Over-pressure prevention, • Open temperature sensor detection, • Safety valve | ||||
| Time | Display | Digital | |||
| Display range |
Sterilizing | 0:00 – 9:59, 0 – 99hours, 0 – 999min.(0:00 – 9:59,10 – 99hours changeable) | |||
| Heating | |||||
| Warming | Variable: 0 – 99hours | ||||
| Chamber dimensions | φ325 x 553mm | φ325 x 733mm | φ370 x 774mm | ||
| Chamber capacity | Effective internal volume:36L, Internal volume:44L |
Effective internal volume:50L, Internal volume:58L |
Effective internal volume:69L, Internal volume:79L |
||
| Chamber material | SUS304 | ||||
| Dimensions (mm) | 410W x 477D x 790Hmm (With protruding:574D) |
410W x 477D x 970Hmm (With protruding:574D) |
470W x 528D x 1003Hmm (With protruding:625D) |
||
| Weight | 50kg | 60kg | 72kg | ||
| Rated voltage | 120V AC | – | |||
| 230V AC | |||||
| Power input | 13A/120V | 17A/120V | – | ||
| 7A/230V | 9A/230V | 13A/230V | |||
| Required power supply | Single-phase 120V AC (50/60 Hz)15A or more |
Single-phase 120V AC (50/60 Hz)20A or more |
– | ||
| Single-phase 230V AC (50/60 Hz)10A or more |
Single-phase 230V AC (50/60 Hz)15A or more |
Single-phase 230V AC (50/60 Hz)15 A or more |
|||
| Power consumption (calorific value) | 1.5kW (1290kcal/h) | 2.0kW (1720cal/h) | 3.0kW (2580cal/h) | ||
| Environmental Conditions | When opereting the autoclave, observe the environmental conditions given below. Ambient temperature: 10 to 35°C Almospheric pressure: 860 to 1060hPa Relative humidity: 30 to 85% Maximum gradient: 2 |
||||
| Accessories | Stainless baskets 1 (φ300 x 182mm) |
Stainless baskets 2 (φ300 x 182mm) |
Stainless baskets 2 (φ345 x 181mm) |
||
| • Chanber bottom Plate 1, • Caster stoppers 4, • Operator’s Manual 1, • Clear folder (for storing the operation manual) 1, • Screw (for attaching the clear folder) 1, • Warranty card 1, • Customer card 1, • Inspection Sheet 1 | |||||
| Model name | SX-300E | SX-500E | SX-700E | ||
| Operating temperature range | Sterilizing | 105 ∼ 135°C (0.019 ∼ 0.212MPa) | |||
| Heating | 45 ∼ 104°C (0 ∼ 0.015MPa) | ||||
| Warming | 45 ∼ 95°C | ||||
| Maximum operating pressure | 0.263MPa | 0.25MPa | |||
| Temperature | Display | Digital | |||
| Pressure gauge | Display | Analog | |||
| Display range | 0 – 0.4MPa | ||||
| Heat source | 1.5kW electric heater | 2.0kW electric heater | 3.0kW electric heater | ||
| Safety device | • Water level sensor, • Leakage breaker, • Lid interlock, • Over-heat prevention, • Over-pressure prevention, • Temperature sensor break detection, • Safety valve | ||||
| Protection type against electrical shock | Class I equipment | ||||
| Time | Display | Digital | |||
| Display range |
Sterilizing | 0:00 – 9:59, 0 – 99hours, 0 – 999min.(0:00 – 9:59,10 – 99hours changeable) | |||
| Heating | |||||
| Warming | Variable: 0 – 99hours | ||||
| Pressure chamber type | PED Category II | ||||
| Chamber dimensions | φ325 x 553mm | φ325 x 733mm | φ370 x 774mm | ||
| Chamber capacity | Effective internal volume:36L, Internal volume:44L |
Effective internal volume:50L, Internal volume:58L |
Effective internal volume:69L, Internal volume:79L |
||
| Chamber material | SUS304 | ||||
| Dimensions (mm) | 410W x 477D x 790Hmm (With projection:574D) |
410W x 477D x 970Hmm (With projection:574D) |
470W x 528D x 1003Hmm (With projection:625D) |
||
| Weight | 50kg | 60kg | 72kg | ||
| Rated voltage | 230V AC | ||||
| Power input | 7A | 9A | 13A | ||
| Required power supply | Single-phase 230V AC (50/60 Hz)10 A or more |
Single-phase 230V AC (50/60 Hz)15 A or more |
Single-phase 230V AC (50/60 Hz)15 A or more |
||
| Power consumption (calorific value) | 1.5kW(1290kcal/h) | 2.0kW(1720kcal/h) | 3.0kW(2580kcal/h) | ||
| Environmental Conditions | When opereting the autoclave, observe the environmental conditions given below. Ambient temperature: 10 to 35°C Almospheric pressure: 860 to 1060hPa Relative humidity: 30 to 85% Maximum gradient: 2 |
||||
| Accessories | Stainless baskets 1 (φ300×182 mm) |
Stainless baskets 2 (φ300×182 mm) |
Stainless baskets 2 (φ345×181 mm) |
||
| • Caster stopper 4, • Chamber bottom Plate 1, • Operator’s Manual 1, • Clear Plastic Accessory Case 1, • Attachment Screw for Clear Plastic Accessory Case 1, • Inspection Sheet 1, • Warranty card 1, • Customer card 1 | |||||
*Please refer to the「 EC Declaration of Conformity」for detailed standard application.
* Specifications and design are subject to change for improvement without prior notice. Please ask for the latest specifications prior to your order and procurement.
CSI Labshop Malaysia is proud to be an authorized dealer for Hirayama HV-Series vertical autoclaves in Malaysia. We provide full support backup with complete installation, training, and commissioning including DOSH (JKKP approval) for your laboratory. Call us to discuss the options and prices.
| HV series |  |
| The Most Advanced Autoclaves with Unique Features | |
 |
Electromechanical lock system |
| By only using a one-touch lever, you con easily and safely Lock & Open the lid | |
  |
| *Electromechanical lock system *Dual-sensing interlock mechanism *Double-sensing system for air evacuation *Programmable auto start *Process status display *Process mode for agar |
Retrofittable accessories (Any combination possible) A : Forced cooling unit F : Floating sensor P : Digital printer W : Automatic water supply Z : All combined(A+F+P+W) |
| Model Effective capacity Chamber size（㎜) Outer dimensions (W×H×D㎜) Max.Steril.temp Process mode Net weight |
HV-25 25liter 240φ×550D 480×950×460 126℃ |
HV-50 50liter 300φ×710D 510×1040×530 135℃ |
HV-85 85liter 420φ×615D 660×1000×650 135℃ |
HV-110 110liter 420φ×795D 660×1180×650 135℃ |
| HVA-85/110 | |
 |
Economical Autoclave for 85/110 Liter Capacities, but Improved Basic Performance with Built-in Cooling Fan |
||
| *Electromechanical lock system *Dual-sensing interlock mechanism *Pulse Exhaust System *Memory function (Program your own) *Space-saving design *Process status display |
|||
| Model Effective capacity Chamber size（㎜) Outer dimensions (W×H×D㎜) Max.Steril.temp Process mode Net weight |
HVA-85 85 liter 420φ×615D 667×1011×652 135℃ |
HVA-110 110 liter 420φ×795D 667×1191×652 135℃ |
|
| HVE-50 | |
 |
New and Economic Autoclave based on Unique Features of HV series |
|
| *Electromechanical lock system *Dual-sensing interlock mechanism *Pulse Exhaust System *Memory function (Program your own) *Space-saving design *Process status display |
Effective capacity : 50liter Chamber size(㎜) : 300φ×710 Outer dimensions(W×H×D㎜): 547×1046×532 Max.Steril.temp : 135℃ Process mode : 3-modes Net weight : 57kg |
|
| HVP-50 | |
 |
New Vertical Autoclave with Vacuum Pump and Drying Cycle | |
| *One-touch Lid Interlock System *Vacuum Pump built-in |
||
| Effective capacity : 50liter Chamber size(㎜) : 300φ×710D Outer dimensions(W×H×D㎜) : 540×1040×630 |
Max.Steril.temp : 135℃ Process mode : 4-modes Net weight : 80kg |
|
What is SRM and CRM?
Certified Reference Materials (CRMs) are ‘controls’ or standards used to check the quality and metrological traceability of products, to validate analytical measurement methods, or for the calibration of instruments. A certified reference material is a particular form of measurement standard.
Reference materials are particularly important for analytical chemistry and clinical analysis.[2] Since most analytical instrumentation is comparative, it requires a sample of known composition (reference material) for accurate calibration. These reference materials are produced under stringent manufacturing procedures and differ from laboratory reagents in their certification and the traceability of the data provided.
Quality management systems involving laboratory accreditation under national and international accreditation/certification standards such as ISO/IEC 17025 require metrological traceability to Certified Reference Materials (where possible) when using reference materials for calibration.[3]
Whilst Certified Reference Materials are preferred where available,[3][4] their availability is limited. Reference Materials that do not meet all the criteria for certified reference materials are more widely available: the principal difference is the additional evidence of metrological traceability and statement of measurement uncertainty provided on the certificate for certified reference materials.[5]
ILAC describes the following five types of reference material:[1]
Source: Wikipedia
CSI Labshop Malaysia is a supplier and has an extensive network of sources for CRMs and SRMs from all over the world. All kinds of reference materials from environmental samples, geological, material characterization, elemental, oil, sedimentary, sand, and much more, call us for more information.